skyfall/rtl8188eu
1
0
Fork 0
mirror of https://github.com/lwfinger/rtl8188eu.git synced 2024-11-10 15:39:38 +00:00
Code Issues Projects Releases Packages Wiki Activity Actions
rtl8188eu/include/Hal8723PwrSeq.h

171 lines
15 KiB
C
Raw Normal View History

rtl8188eu: Remove all trailing spaces from code Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
2014-12-19 06:59:46 +00:00
#ifndef __HAL8723PWRSEQ_H__
#define __HAL8723PWRSEQ_H__
/*
Check document WM-20110607-Paul-RTL8723A_Power_Architecture-R02.vsd
There are 6 HW Power States:
0: POFF--Power Off
1: PDN--Power Down
2: CARDEMU--Card Emulation
3: ACT--Active Mode
4: LPS--Low Power State
5: SUS--Suspend
The transision from different states are defined below
TRANS_CARDEMU_TO_ACT
TRANS_ACT_TO_CARDEMU
TRANS_CARDEMU_TO_SUS
TRANS_SUS_TO_CARDEMU
TRANS_CARDEMU_TO_PDN
TRANS_ACT_TO_LPS
TRANS_LPS_TO_ACT
TRANS_END
*/
#include "HalPwrSeqCmd.h"
#include "rtl8723a_spec.h"
#define RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS 15
#define RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS 15
#define RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS 15
#define RTL8723A_TRANS_SUS_TO_CARDEMU_STEPS 15
#define RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS 15
#define RTL8723A_TRANS_PDN_TO_CARDEMU_STEPS 15
#define RTL8723A_TRANS_ACT_TO_LPS_STEPS 15
#define RTL8723A_TRANS_LPS_TO_ACT_STEPS 15
#define RTL8723A_TRANS_END_STEPS 1
#define RTL8723A_TRANS_CARDEMU_TO_ACT \
/* format */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
{0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0}, /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/ \
{0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x67[0] = 0 to disable BT_GPS_SEL pins*/ \
{0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS},/*Delay 1ms*/ \
{0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, 0}, /*0x00[5] = 1b'0 release analog Ips to digital ,1:isolation*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0},/* disable SW LPS 0x04[10]=0*/ \
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1 power ready*/ \
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* release WLON reset 0x04[16]=1*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* disable HWPDN 0x04[15]=0*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, (BIT4|BIT3), 0},/* disable WL suspend*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* polling until return 0*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT0, 0},/**/ \
{0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 1},/*0x4C[23] = 0x4E[7] = 1, switch DPDT_SEL_P output from WL BB */\
#define RTL8723A_TRANS_ACT_TO_CARDEMU \
/* format */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
{0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/ \
{0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/*0x4C[23] = 0x4E[7] = 0, switch DPDT_SEL_P output from register 0x65[2] */\
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \
{0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5}, /*0x00[5] = 1b'1 analog Ips to digital ,1:isolation*/ \
{0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/ \
#define RTL8723A_TRANS_CARDEMU_TO_SUS \
/* format */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4|BIT3, (BIT4|BIT3)}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \
{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SDIO SOP option to disable BG/MB/ACK/SWR*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3|BIT4}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/
#define RTL8723A_TRANS_SUS_TO_CARDEMU \
/* format */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/
#define RTL8723A_TRANS_CARDEMU_TO_CARDDIS \
/* format */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07=0x20 , SOP option to disable BG/MB*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, BIT2}, /*0x04[10] = 1, enable SW LPS*/ \
{0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1}, /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/ \
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/
#define RTL8723A_TRANS_CARDDIS_TO_CARDEMU \
/* format */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\
{0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/\
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/ \
{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*PCIe DMA start*/
#define RTL8723A_TRANS_CARDEMU_TO_PDN \
/* format */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \
{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK|PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/ \
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/* 0x04[16] = 0*/\
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/
#define RTL8723A_TRANS_PDN_TO_CARDEMU \
/* format */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/
#define RTL8723A_TRANS_ACT_TO_LPS \
/* format */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/ \
{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/ \
{0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
{0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
{0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
{0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/ \
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*Whole BB is reset*/ \
{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/ \
{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/ \
{0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/*When driver enter Sus/ Disable, enable LOP for BT*/ \
{0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/ \
#define RTL8723A_TRANS_LPS_TO_ACT \
/* format */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\
{0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\
{0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\
{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*. 0x08[4] = 0 switch TSF to 40M*/\
{0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]=0 TSF in 40M*/\
{0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6|BIT7, 0}, /*. 0x29[7:6] = 2b'00 enable BB clock*/\
{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*. 0x101[1] = 1*/\
{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF}, /*. 0x100[7:0] = 0xFF enable WMAC TRX*/\
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1|BIT0, BIT1|BIT0}, /*. 0x02[1:0] = 2b'11 enable BB macro*/\
{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/
#define RTL8723A_TRANS_END \
/* format */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
{0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,0,PWR_CMD_END, 0, 0}, //
rtl8188eu: Convert typedef WLAN_PWR_CFG to struct wl_pwr_cfg Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
2015-03-13 15:59:57 +00:00
extern struct wl_pwr_cfg rtl8723A_power_on_flow[RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS+RTL8723A_TRANS_END_STEPS];
extern struct wl_pwr_cfg rtl8723A_radio_off_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_END_STEPS];
extern struct wl_pwr_cfg rtl8723A_card_disable_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723A_TRANS_END_STEPS];
extern struct wl_pwr_cfg rtl8723A_card_enable_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723A_TRANS_END_STEPS];
extern struct wl_pwr_cfg rtl8723A_suspend_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS+RTL8723A_TRANS_END_STEPS];
extern struct wl_pwr_cfg rtl8723A_resume_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS+RTL8723A_TRANS_END_STEPS];
extern struct wl_pwr_cfg rtl8723A_hwpdn_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723A_TRANS_END_STEPS];
extern struct wl_pwr_cfg rtl8723A_enter_lps_flow[RTL8723A_TRANS_ACT_TO_LPS_STEPS+RTL8723A_TRANS_END_STEPS];
extern struct wl_pwr_cfg rtl8723A_leave_lps_flow[RTL8723A_TRANS_LPS_TO_ACT_STEPS+RTL8723A_TRANS_END_STEPS];
rtl8188eu: Remove all trailing spaces from code Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
2014-12-19 06:59:46 +00:00
#endif
Reference in a new issue Copy permalink