rtl8188eu/include/Hal8188EPwrSeq.h

/* SPDX-License-Identifier: GPL-2.0 */
/* Copyright(c) 2007 - 2016 Realtek Corporation. All rights reserved. */


#ifndef __HAL8188EPWRSEQ_H__
#define __HAL8188EPWRSEQ_H__

#include "HalPwrSeqCmd.h"

/*
	Check document WM-20110607-Paul-RTL8188E_Power_Architecture-R02.vsd
	There are 6 HW Power States:
	0: POFF--Power Off
	1: PDN--Power Down
	2: CARDEMU--Card Emulation
	3: ACT--Active Mode
	4: LPS--Low Power State
	5: SUS--Suspend

	The transision from different states are defined below
	TRANS_CARDEMU_TO_ACT
	TRANS_ACT_TO_CARDEMU
	TRANS_CARDEMU_TO_SUS
	TRANS_SUS_TO_CARDEMU
	TRANS_CARDEMU_TO_PDN
	TRANS_ACT_TO_LPS
	TRANS_LPS_TO_ACT

	TRANS_END

    PWR SEQ Version: rtl8188E_PwrSeq_V09.h
*/
#define	RTL8188E_TRANS_CARDEMU_TO_ACT_STEPS	10
#define	RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS	10
#define	RTL8188E_TRANS_CARDEMU_TO_SUS_STEPS	10
#define	RTL8188E_TRANS_SUS_TO_CARDEMU_STEPS	10
#define	RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS	10
#define	RTL8188E_TRANS_PDN_TO_CARDEMU_STEPS	10
#define	RTL8188E_TRANS_ACT_TO_LPS_STEPS	15
#define	RTL8188E_TRANS_LPS_TO_ACT_STEPS	15
#define	RTL8188E_TRANS_END_STEPS	1


#define RTL8188E_TRANS_CARDEMU_TO_ACT														\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1    power ready*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0 | BIT1, 0}, /* 0x02[1:0] = 0	reset BB*/			\
	{0x0026, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7}, /*0x24[23] = 2b'01 schmit trigger */	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0}, /* 0x04[15] = 0 disable HWPDN (control by DRV)*/\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4 | BIT3, 0}, /*0x04[12:11] = 2b'00 disable WL suspend*/	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0}, /*0x04[8] = 1 polling until return 0*/	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT0, 0}, /*wait till 0x04[8] = 0*/	\
	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*LDO normal mode*/	\

#define RTL8188E_TRANS_ACT_TO_CARDEMU													\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/	\
	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4}, /*LDO Sleep mode*/	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/	\

#define RTL8188E_TRANS_CARDEMU_TO_SUS													\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, BIT3}, /*0x04[12:11] = 2b'01enable WL suspend*/	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, BIT3 | BIT4}, /*0x04[12:11] = 2b'11enable WL suspend for PCIe*/	\
	{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, BIT7}, /*  0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */	\
	{0x0041, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*Clear SIC_EN register 0x40[12] = 1'b0 */	\
	{0xfe10, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4}, /*Set USB suspend enable local register  0xfe10[4]=1 */	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/

#define RTL8188E_TRANS_SUS_TO_CARDEMU													\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/

#define RTL8188E_TRANS_CARDEMU_TO_CARDDIS													\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0026, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7}, /*0x24[23] = 2b'01 schmit trigger */	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/	\
	{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*  0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */	\
	{0x0041, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*Clear SIC_EN register 0x40[12] = 1'b0 */	\
	{0xfe10, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4}, /*Set USB suspend enable local register  0xfe10[4]=1 */	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/

#define RTL8188E_TRANS_CARDDIS_TO_CARDEMU													\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/

#define RTL8188E_TRANS_CARDEMU_TO_PDN												\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/* 0x04[16] = 0*/\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/

#define RTL8188E_TRANS_PDN_TO_CARDEMU												\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/

	/* This is used by driver for LPSRadioOff Procedure, not for FW LPS Step */
#define RTL8188E_TRANS_ACT_TO_LPS														\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x7F},/*Tx Pause*/	\
	{0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
	{0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
	{0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
	{0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/	\
	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/	\
	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/	\
	{0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/	\


#define RTL8188E_TRANS_LPS_TO_ACT															\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\
	{0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\
	{0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\
	{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*.	0x08[4] = 0		 switch TSF to 40M*/\
	{0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]=0  TSF in 40M*/\
	{0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6 | BIT7, 0}, /*.	0x29[7:6] = 2b'00	 enable BB clock*/\
	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*.	0x101[1] = 1*/\
	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, /*.	0x100[7:0] = 0xFF	 enable WMAC TRX*/\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1 | BIT0, BIT1 | BIT0}, /*.	0x02[1:0] = 2b'11	 enable BB macro*/\
	{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*.	0x522 = 0*/

#define RTL8188E_TRANS_END															\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, 0, PWR_CMD_END, 0, 0},


	extern WLAN_PWR_CFG rtl8188E_power_on_flow[RTL8188E_TRANS_CARDEMU_TO_ACT_STEPS + RTL8188E_TRANS_END_STEPS];
	extern WLAN_PWR_CFG rtl8188E_radio_off_flow[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188E_TRANS_END_STEPS];
	extern WLAN_PWR_CFG rtl8188E_card_disable_flow[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS + RTL8188E_TRANS_END_STEPS];
	extern WLAN_PWR_CFG rtl8188E_card_enable_flow[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS + RTL8188E_TRANS_END_STEPS];
	extern WLAN_PWR_CFG rtl8188E_suspend_flow[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188E_TRANS_CARDEMU_TO_SUS_STEPS + RTL8188E_TRANS_END_STEPS];
	extern WLAN_PWR_CFG rtl8188E_resume_flow[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188E_TRANS_CARDEMU_TO_SUS_STEPS + RTL8188E_TRANS_END_STEPS];
	extern WLAN_PWR_CFG rtl8188E_hwpdn_flow[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS + RTL8188E_TRANS_END_STEPS];
	extern WLAN_PWR_CFG rtl8188E_enter_lps_flow[RTL8188E_TRANS_ACT_TO_LPS_STEPS + RTL8188E_TRANS_END_STEPS];
	extern WLAN_PWR_CFG rtl8188E_leave_lps_flow[RTL8188E_TRANS_LPS_TO_ACT_STEPS + RTL8188E_TRANS_END_STEPS];

#endif /* __HAL8188EPWRSEQ_H__ */